Evinrude Electric Motor Manual

Evinrude Electric Motor Manual 5,6/10 3205votes

cockatrice mac download

Evinrude Electric Motor Manual

Download 125 Evinrude Outboard Motor PDF manuals. User manuals, Evinrude Outboard motor Operating guides and Service manuals. With a fast-idle choke system for easy and fast starting, Evinrude portable engines make boating that much easier. Evinrude E-TEC Direct Injection engines are not only cleaner, but has all the best qualities of a four-stroke. Find out what makes us best-in-class. 1990-2001 Johnson Evinrude Service Manual 1.25 to 70 HP - PDF Service Manual. Troubleshooting outline of monitor tachometer starter motor, electric starter.

1971-1989 Evinrude 1-60hp Service Manual. Thermo switch -1977 A-36 50 hp w/manual Start --1980-85 A-37 55 hp w/electric start --1977 A-38 50. Motor does not.

A few things: 1. That model was a standard on my 96 Stratos. It just had a Johnson sticker on the side instead of Evinrude. The thrust was 47lbs and it pushed my 18ft bass boat until about 3 months ago.

Those TM are tanks!! You can purchase parts, props, pins, covers, etc. You may want to be careful as I believe they only come in 42 in shaft length. That may be too short for a toon. Also, IMO that would be underpowered for a 24ft toon. There are two sized props for that motor, I believe it was an 8' and a 12' You'll have to check the bottom of the prop to determine which one fits.

That's awesome info guys. Cool to know the support for these trolling motors is good. I might keep looking. Really wanna get setup on my toon, but hoping to find a more powerful motor.

I have this old dinky motorguide trolling motor with like a 5 inch prop that pushed my old 24' toon around nice on 24 volt. I am going to sleep on it but might give this thing a try. I am getting it for reasonable money.

I can alway upgrade later once the funds get better. Really wanna start fishing from this toon. Summer pattern is kicking in.

I believe they are a 56lb thrust with the larger prop like the one pictured. You also nee the 'pan' that goes with that motor to install it correctly. How much was it listed for on CL? Correct the 12' prop models were call High Output.

They are three speed and 12 or 24 volts. The 8' prop models were 41#.

Evinrude Electric Motor ManualEvinrude Electric Motor Manual

The Pan that goes under the mount has the rubber pads that the motor rests on when stowed. The 'Go Fast' boat crowd likes those old motors since they are so lightweight. This is the HO model on a 12' jon boat I used to have. 1996 Golf Haynes Manual on this page. A few things: 1. That model was a standard on my 96 Stratos. It just had a Johnson sticker on the side instead of Evinrude. The thrust was 47lbs and it pushed my 18ft bass boat until about 3 months ago.

Those TM are tanks!! You can purchase parts, props, pins, covers, etc. You may want to be careful as I believe they only come in 42 in shaft length. That may be too short for a toon. Also, IMO that would be underpowered for a 24ft toon. There are two sized props for that motor, I believe it was an 8' and a 12' You'll have to check the bottom of the prop to determine which one fits.

Evinrude Electric Motor Manual

Good luck That motor was available with a 36' shaft, 42' shaft and a 48' shaft. I had all three. Those motors are great. We had one on our '93 stratos until this spring. The steering cable snapped for about the fourth time so we finally decided to get one with more thrust. For a smaller boat you can't beat it, especially for $125. And if you're looking for information on the motor, get on Smithville Marine's website and go to the parts section.

Type in the model number on the side of the motor and it should tell you just about everything you need to know about it. This was helpful for me this spring when the cable snapped.

The Johnson-Evinrude Workshop manual downloads for the above listed models describes the service procedures for the complete vehicle. Follow the Maintenance Schedule recommendations to ensure that the outboard is in peak operating condition. Performing the scheduled maintenance is very important. It compensates for the initial wear that occurs during the life of the outboard motor. All chapters in the Workshop Manual apply to the whole vehicle and illustrates procedures for removal/installation of components that are in detailed step-by-step fashion.

Most all Workshop manual chapters start with an assembly or system illustration, diagrams, exploded parts view, pictures, service information and troubleshooting for the section. The subsequent pages give detailed procedures.

Evinrude Electric Motor Manual

PROBLEM 1: ENGINE TURNS OVER BUT WILL NOT START OR STARTS HARD WHEN COLD Possible Cause Corrective Action Improper starting procedure. Check procedure, as outlined in “Operation and Maintenance Manual.” Fuel tank empty; improperly mixed fuel; contaminants (water, dirt, etc.) in fuel. Check fuel in fuel tank and replace or add. Fuel tank air vent closed or restricted. Air vent must be open and free from contaminants. A pinched or restricted fuel line.

Check, and replace as needed. Dirty or restricted fuel filter.

Check, replace or clean. Enrichener valve not operating.

Check enrichener system. (Refer to “Enrichener System” following.) An inlet needle (in carburetor) that is stuck open or closed. (A needle stuck open, will cause a flooding condition. A needle stuck closed, will prevent fuel from entering carburetor.) Remove, clean, or replace. Anti-Siphon valve restricting fuel flow. Refer to “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, following.

See “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, page 3A-1. PROBLEM: ENGINE FLOODS Possible Cause Corrective Action Dirt or foreign particles are preventing inlet needle from seating. Flush out inlet seat and clean inlet needle.